|
MAXPEDITION
LIGER PRODUCTS 1.5" GUN BELT
About LIGER™
Gun Belt
The LIGER™ Gun Belt represents a major break-through in gun belt
design, utilizing custom components and proprietary processes developed
by and available exclusively from LIGER™ PRODUCTS.
Ligerthane™
Material
The Ligerthane™
belt material is a 21st century composite developed by LIGER™ PRODUCTS.
Thanks to its high-strength resin-embedded polyester fabric core, Ligerthane™
possesses over 2,000 lbs of tensile strength with over 300 lbs of hole
pull strength. The highly abrasion- resistant polyurethane coating makes
the belt totally impervious to water, mildew, rot and resistant to many
common solvents. Ligerthane™ is flexible along its length for comfort
yet stiff along its width so you can carry holsters, sheaths, or pouches
without the belt sagging or twisting. Ligerthane™ has a super grip
interior so the belt stays put and a LigerDerm™ patterned exterior
that gives it the look and feel of leather; it’s nice enough to
wear with your BDU’s or dress pants and perfect for discrete CCW.
Best of all, Ligerthane™ is easy-to-clean, just rinse with mild
detergent and wipe dry.
| Liger
Belt |
MAX-LGB1501 |
| Buckle
Material: |
6061
T6
Aircraft Aluminum |
| Buckle
Closure: |
Hook |
| Belt
Material: |
Ligerthane |
Bacteria
/ Mildew
resistant: |
Yes |
| Waterproof: |
Yes |
| Hole
pull strength: |
300lbs |
| Tensile
strength: |
2000lbs |
| Construction: |
Riveted |
| Can
be sterilized: |
Yes |
|
LIGER™ Buckle
and Construction
The LIGER™ Gun Belt buckle is painstakingly machined from a
solid billet of T6-6061 aircraft aluminum with our exclusive integral
hook design. After a two-step finishing process, Type-III hard-anodized
finish (MILSPEC-A-8625) is applied for incredible wear resistance. The
LIGER™ buckle and Ligerthane™ belt are riveted together using
robust 3/16” stainless steel rivets resulting in a strong, permanent
one-piece construction.
 Sizing
Instructions
LIGER™
belt sizing is based on ACTUAL WAIST CIRCUMFERENCE in inches. Each belt
is handmade one at a time upon receipt of order based on the sizing information
you provide. In order to prevent ordering an incorrect size and to insure
a tailored fit, please carefully read the following simple measuring instructions:
- Do NOT order according to your pants size. Measure your waist
circumference in inches with a cloth tailor’s tape (or a measuring
tape).
- Put
the tape through the loops on your pants as you would usually wear them,
measuring all the way around your waist with any equipment you wear
on your belt or inside your waist band like guns, knives, phones, pouches,
etc.
- This
waist circumference measurement is your primary size, if it is an
odd number (ex: 41 inches), order the next higher even number size (Size
42).
- We provide
two additional holes on either side of the primary hole at one inch
intervals for fine adjustment.
- Each
belt is custom built to order and components are permanently rivetted
together, consuming the components and rendering them impossible
to reuse. A twenty-five percent (25%) restocking fee will be charged
for items returned for incorrect sizing. If additional holes are
needed, you can get them punched at any leather or luggage shop.
Product
Warranty
LIGER™
PRODUCTS extends a limited lifetime warranty covering all products against
manufacturer’s defects including flaws in material and workmanship.
Products covered under our warranty will be repaired or replaced at our
discretion, free of charge.
(Warranty
issues are handled by MAXPEDITION / LIGER PRODUCTS not OneStopKnifeShop.com) |
